TECHNICAL BULLETIN |
DESCRIPTION |
Technical Bulletin 40 |
CB-180 Electronics Boards (AAI PN 2012803-00X - Caveats) |
Technical Bulletin 41 |
MDS 94.1 Service Bulletin and How to Acquire |
Technical Bulletin 44 |
FCU Local Protocol Terminal Interface |
Technical Bulletin 45 |
Setup & Calibration of I/O on 6400 & 6700 Series FCUs |
Technical Bulletin 46 |
Early Model Series 6400 Flow Computers - Potential Problems |
Technical Bulletin 47 |
Totalflow Configuration Read / Write Programs |
Technical Bulletin 48 |
Btu Transmitter & Field Procedure for Baking Columns |
Technical Bulletin 49 |
Gaskets and Rivets |
Technical Bulletin 50 |
Modem Communications |
Technical Bulletin 51 |
Buss loading of RTS signal on RS-485 communications |
Technical Bulletin 52 |
Quad-AO problem with the CB-180 and CB-181 board |
Technical Bulletin 53 |
Jumper settings for new 2X24 LC Display |
Technical Bulletin 54 |
MDS-2310 New wiring to support lower current consumption |
Technical Bulletin 55 |
Third party items supported by Totalflow Technical Support |
Technical Bulletin 56 |
FS/2 PCCU Software Downloading Procedure (2015134-002 AB) |
Technical Bulletin 57 |
Expanded I/O RS-485 bus Termination Procedure for New Style Electronic Boards |
Technical Bulletin 58 |
6713 AI #2 Calibration |
Technical Bulletin 59 |
Flow Computer Lead Acid Battery Preventative Maintenance |
Technical Bulletin 60 |
History of the Expanded I/O (2012901 to 2017333) |
Technical Bulletin 61 |
Procedure for setting up 6400/6700 Custom Display |
Technical Bulletin 62 |
Procedure for using LPX Program |
Technical Bulletin 63 |
Procedure for 6400/6700 AI Calibration w/ Custom Display |
Technical Bulletin 64 |
FS/2 Battery Replacement Procedure |
Technical Bulletin 65 |
Shoppe and Faeser AMU Cable Problem |
Technical Bulletin 66 |
Reverse Polarity on Btu8000 Transmitter |
Technical Bulletin 67 |
Removing drain screw from Enclosures |
Technical Bulletin 68 |
Modifications Required for MDS-2310/MDS-9810 Piggy Back Operation |
Technical Bulletin 69 |
Storage procedures for Btu Transmitter |
Technical Bulletin 70 |
Potential Power-up problem with CB-180, RTU and Expanded I/O boards |
Technical Bulletin 71 |
Launching WinCCU Scheduler from a command line interface |
Technical Bulletin 72 |
Procedure for the HCOMW101.EXE Program for Husky FS2 |
Technical Bulletin 73 |
Procedure for downloading flash programs |
Technical Bulletin 74 |
Analysis Download to FCU using WinCCU |
Technical Bulletin 75 |
Volume Related PCCU and Host downloads not Causing a Volume Change in Flow Computer |
Technical Bulletin 76 |
DP Pressure correction problem on a subset of CB-180 firmware |
Technical Bulletin 77 |
Foxboro silicone fluid leakage problem |
Technical Bulletin 78 |
UCI2 Product Update Notice |
Technical Bulletin 79 |
Analog to Digital Conversion Error using multiple communication ports |
Technical Bulletin 80 |
Cold boot procedure for newer style ram chips |
Technical Bulletin 81 |
Fairchild actuator (software) fix (REPLACED by BULLETIN # 92) |
Technical Bulletin 82 |
PTC Fuses Being Added To Totalflow Electronic Circuit Boards |
Technical Bulletin 83 |
Potential of charger grounding problem with 6700 Flow Computer |
Technical Bulletin 84 |
Potential for too many log records for one day |
Technical Bulletin 85 |
Expanded I/O Analog Output Circuitry Voltage Limitation |
Technical Bulletin 86 |
UCI2 Radio Wiring Recommendation to Prevent Unintentional Keying of Transmitter |
Technical Bulletin 87 |
Non-compliance of XF11 interface between EXIO and CB181 FCU software |
Technical Bulletin 88 |
UCI2 configured as an RS 232 to RS485 converter |
Technical Bulletin 89 |
AP location parameter change required when using BYS AMUs |
Technical Bulletin 90 |
Hoffman Latch Notice |
Technical Bulletin 91 |
6400/6700 Pipe Mounting Bracket Notice |
Technical Bulletin 92 |
Fairchild Actuator Hardware Modification |
Technical Bulletin 93 |
LevelMaster Loss of Level and Temperature Readings |
Technical Bulletin 94 |
Analog Measurement Unit (AMU) Product Improvement |
Technical Bulletin 95 |
Static Pressure Correction, Explanation and Troubleshooting Guide |
Technical Bulletin 96 |
LevelMaster Sensor Electronic Board Replacment Procedure |
Technical Bulletin 97 |
ABB Multivariable Setup |
Technical Bulletin 98 |
WinCCU SQL Server Setup |
Technical Bulletin 99 |
XSeries EPROM and FLASH Upgrade Procedure |
Technical Bulletin 100 |
Incorrect FCU Mounting U-Bolt shipped in February 2003 |
Technical Bulletin 101 |
Obsolescence of the Radio Modem (Div 1) Assembly and Universal Communication Interface (UCI) Electronic Boards |
Technical Bulletin 102 |
Multiple Log Periods without the Contract Day Incrementing |
Technical Bulletin 103 |
Configuring an AGA-7 Application for Liquid Measurement with Turbine or Positive Displacement Meters |
Technical Bulletin 105 |
MicroFLO and XSeries Trend and Therms Database Logging Issue |
Technical Bulletin 106 |
NX19 Supercompressibility Equation Using Fixed FtFp |
Technical Bulletin 107 |
Method to Set Up and Use the Btu Transmitter DSM Command |
Technical Bulletin 108 |
XSeries and MicroFLO -99 & -100 Event Issue |
Technical Bulletin 109 |
Phase Out and Upgrade Options for the Model 6600 Flow Computer Unit |
Technical Bulletin 110 |
MicroFLO and XSeries Potential Collection Problem Using the Husky FS2 or MP2500 |
Technical Bulletin 111 |
LevelMaster RS-485 Electrical Changes (Revision AY Boards) |
Technical Bulletin 112 |
Replacement Program for the Model 8000/8100 Btu/CV Transmitter Stream Selector |
Technical Bulletin 113 |
Tuning ABB’s Modbus Multivariable's Static Pressure Response Time
Download AD Trim Program Referenced in Technical Bulletin 113 |
Technical Bulletin 114 |
Scale Analog Inputs without Performing Calibration |
Technical Bulletin 115 |
AMU DP Cell Ribbon Cable Notice |
Technical Bulletin 116 |
IMV, XIMV and Modbus Multivariable DP Zero Stabilization |
Technical Bulletin 117 |
Analyzer Interface Unit (AIU) Upgrade Offer |
Technical Bulletin 118 |
Configuring XSeries and µFLO FCUs and RTUs as Modbus Slaves |
Technical Bulletin 119 |
Local/Remote PCCU Protocol Switch Issue Related to the CB180, CB181 and 6400 Flow Computers |
Technical Bulletin 120 |
TDS5.25 Install Problem |
Technical Bulletin 121 |
Older Vintage AMUs not Compatible with XFC Flow Computers |
Technical Bulletin 122 |
FLO (microFLO) Local Communications Port Issue |
Technical Bulletin 123 |
Btu 8000/8100 Noisy Baseline caused by Defective or Damaged Detector Beads |
Technical Bulletin 124 |
Effect of Water in Helium Carrier in Btu 8000/8100 |
Technical Bulletin 125 |
Btu 8000/8100 Troubled Site Survey |
Technical Bulletin 126 |
Switched Voltage Battery Issue on Model 6200 microFLO and XSeries Products |
Technical Bulletin 127 (pdf, 0.07 MB) |
Testing the Stream Pressure on a Btu 8000 |
Technical Bulletin 128 (pdf, 0.20 MB) |
Testing for Sample Flow on a Btu 8000 |
Technical Bulletin 129 (pdf, 0.13 MB) |
Btu 8000 Flash Update Procedure |
Technical Bulletin 130 |
Peak Find and Calibration of a Btu 8000 |
Technical Bulletin 132 |
microFLO FLASH 2101048-021 Enhancement |
Technical Bulletin 133 |
6400/6700 Error Code -32768 When Installing New XIMV Spare Part |
Technical Bulletin 134 |
Communications Module Sulfide Contamination Issue |
Technical Bulletin 135 |
Correcting Problems with WinCCU32 Analysis Edits |
Technical Bulletin 136 |
XSeries Flow Computers Configuring Quad AO Modules |
Technial Bulletin 137 |
Save and Restore Utility and Potential Calibration Issues |
Technical Bulletin 138 |
Adding "Flow Time" to a Flow Computer Display |
Technical Bulletin 139 |
Manual Gating of CO2 of the Btu 8000 for Analyzing Very Low Concentrations of CO2 |
Technical Bulletin 140 |
Upstream vs Downstream Pressure Tap Explanation |
Technical Bulletin 144 |
Field Repair of Btu 8000 GC Modules with Low Sample Flow Fault 144 |
Technical Bulletin 145 |
NGC 8206 Losing Pressure and Timing Settings when Analog Board Resets |
Technical Bulletin 146 |
Keypad General Navigation and Setup for Calibrating Transducers |
Technical Bulletin 147 |
Reverting Back to NGC Factory Configuration Defaults |
Technical Bulletin 148 |
Connecting NGC Over TCPI/P Ethernet to PCCU/NGC Software |
Technical Bulletin 149 |
Proper Grounding of External Three-Wire Transmitters |
Technical Bulletin 150 |
Updating the NGCs Analog Processor Electronic Board FLASH (Blackfin) |
Technical Bulletin 151 (pdf, 0.02 MB) |
Potential Noisy Readings when Checking or Calibrating 6600 Flow Computers with PCCU32 Versions of Laptop Software |
Technical Bulletin 152 (pdf, 0.25 MB) |
NGC Calibration Techniques (Technical Discussion) |
Technical Bulletin 153 (pdf, 0.15 MB) |
Analog Input Calibration Procedure for the XFC/XRC |
Technical Bulletin 154 (pdf, 0,15 MB) |
Adam RS-485 Quad AO Converter to NGC Setup and Operation |
Technical Bulletin 155 (pdf, 0,32 MB) |
NGC Controller Module Interface Gasket Torque Specification Notice |
Technical Bulletin 156 (pdf, 0,03 MB) |
NGC Analytical Module (Burkert Valve Arrangement) Replacement Instructions |
Technical Bulletin 157 (pdf, 0,07 MB) |
NGC Calibration Using Calibration Blends without Neo-Pentane |
Technical Bulletin 158 (pdf, 0,04 MB) |
NGC Velocity of Sound Application |
Technical Bulletin 159 (pdf, 0,18 MB) |
Using 4-20 mA Transmitters with 12 Volt Powered Flow Computer |
Technical Bulletin 160 (pdf, 0,05 MB) |
Btu 8000/8100 Analog Controller Module (ACM) Extended Warranty |
Technical Bulletin 161 (pdf, 0,05 MB) |
Updating the NGC'a Digital Processor Electronic Board FLASH (totalflow.exe) |
Technical Bulletin 162 (pdf, 0,04 MB) |
Calibration Check Events not Matching User's Entry |
|
|